This page has specific product information. For general information on inverters and comparison of the different types of inverters, go to General Inverter Information

XANTREX XW GRID TIE or OFF GRID POWER SYSTEM

Backwoods has taken the leap! Given the nationwide tax incentives and the fact that so many grid-connected folks call us on a daily basis looking for a battery based backup system with the ability to sell excess energy to the utility, we have decided to introduce the Xantrex XW Power System. 

With the XW system, Xantrex has designed a system with an emphasis on performance, ease of installation, and low maintenance. In addition to being an excellent choice for any off-grid application, the XW system operates similarly to typical battery-less grid-tie solar systems but with the added benefit of being able to provide uninterrupted backup power during utility outages. With over 7 million households losing power for more than an hour each year, incorporating a back-up power system is common sense.

Utilizing batteries as a back-up power source is much more reliable and economical compared to fuel-powered generators. Generators are mechanical devices which require regular maintenance and are subject to failure when you need them most, during an outage. Batteries have no moving parts. Once installed and programmed, the XW system operates silently and works automatically; there are no switches to throw; buttons to push; or cords to connect.

System Features:

		Integrated balance-of-systems components
		120/240-volt split-phase operation and true sine wave output
		Unsurpassed surge capacity - innovative Full Digital Control regulates voltage to prevent a drop during a power surge. Full 200% rated output power is delivered to the load
		Efficient, power factor corrected, high-current, multistage battery charging
		Certified to UL1741 and CSA for utility-interactive applications
		Easy and inexpensive to install (does not arrive pre-assembled)
		Local display on inverter shows output power, charge current and battery level, to provide system status at a glance
		Designed for easy field installation with manageable building blocks

 For Complete System Details, please visit:
www.xantrex.com/xw

XW HYBRID INVERTER/CHARGER

XW POWER DISTRIBUTION PANEL

Accommodates both AC and DC breakers and wiring for three XW Hybrid Inverter/Chargers and four XW Solar Charge Controllers   Includes breakers and wiring to connect to XW Hybrid Inverter/Charger   Wiring is labeled and cut-to-length, ready to connect to inverter   Uses flexible Arctic Ultraflex Blue™ wires   Multiple knockouts on sides, top, bottom and back of unit   Includes mounting back plate and and XW Conduit Box XW POWER DISTRIBUTION PANEL: XWPDP: $1200.00 + $45.00 shipping to a lower 48 address:  Click this link for

XW SYSTEM CONTROL PANEL

The XW SCP is a Xanbus™-enabled device featuring a graphical, backlit LCD screen that displays system configuration and diagnostic information for all devices connected to the network. When installed as an XW System accessory, the XW SCP eliminates the need for separate control panels for each device and gives a single point of control to set up and monitor an entire XW Power System.

Interfaces with:
XW4024, XW4548, XW6048 Inverter/Charger(s), XW Solar Charge Controller,
XW Auto Generator Start

XW SYSTEM CONTROL PANEL: XW SCP: $270.00
Click this link for

XW AUTOMATIC GENERATOR START CONTROL

The XW AGS is a Xanbus™-enabled device that can automatically activate a generator to provide an XW Series Inverter/Charger with power to recharge depleted batteries or assist with heavy loads. Compatible with popular generators, the XW AGS adds intelligence to power management and eliminates time spent monitoring batteries and inverter loads. The XW AGS can be configured to start the generator in response to low battery voltage, thermostat operation, or load size on the inverter battery. A quiet-time setting prevents the generator from starting at inconvenient times. The LCD display shows the status of the XW AGS, while all user-defined settings are programmed through the XW System Control Panel.

Interfaces with:
XW Hybrid Inverter/Charger(s), XW Solar Charge Controller(s),
and XW SCP

XW AUTOMATIC GENERATOR START CONTROL: XW AGS: $180
Click this link for

XW MPPT60 CHARGE CONTROLLER

For 12, 24, 36, 48, or 60 volt battery banks

		Two or three-stage charging process, with manual equalization to maximize system performance and maintain expected battery life
		Maximum Power Point Tracking (MPPT) to deliver the maximum available power from a PV array to a battery bank
		Configurable auxiliary power output
		Two-line, 16-character liquid crystal display (LCD) and four buttons for configuration and system monitoring in stand-alone applications
		Battery Temperature Sensor (BTS) to provide automatically temperature-compensated battery charging
		The Charge Controller is able to communicate its settings and activity to other Xanbus™-enabled devices

XW MPPT60 CHARGE CONTROLLER: $585.00 + $15.00 shipping to a lower 48 address click on this link for

Return to the top

OUTBACK
VFX and FX INVERTERS
TRUE SINE WAVE 

STACKABLE FOR HIGHER POWER. 12, 24, OR 48 VOLT BATTERY

VFX/FX Turbo are true sine wave inverter with battery charger and 60 amp automatic AC transfer relay. Output is 2000 to 3600 watts continuous. Surge of 70 amps AC for 1msec each. These inverter can operate alone, or with up to eight together.  No-load power used is 3 watts when in automatic sleep-mode (on loads on); or 20 watts if programmed to keep AC on full time. Peak efficiency is greater than 90%. The FX series is completely sealed against dust and moisture, the die-cast aluminum housing protects and cools with the externally mounted fan for greater battery charging results..

Battery charging current ranges from 35 amps to 125 amps depending on the model.. Automatic programmable generator start is included.

These Inverters  REQUIRE THE MATE METER AND CONTROLLER to initially program features or to stack inverters together. Also see complete Outback power center system. 2 year Warranty.

MODEL	WATTS	VOLTAGE	CHARGE AMPS	PRICE	BUY NOW
I-OBK VFX2812	2,800	12	125	$2295 SALE: $2065.50
I-OBK VFX3524	3,500	24	85	$2295 SALE: $2065.50
I-OBK VFX3648	3,600	48	45	$2295 SALE: $2065.50
I-OBK FX2012 Turbo	2,000	12	100	$2125
I-OBK FX2524 Turbo	2,500	24	55	$2125
I-OBK FX3048 Turbo	3,000	48	35	$2125
Shipping for any VFX/FX inverter........$40
I-OBK TEMP battery temperature sensor corrects charge voltage.....$29
I-OBK FXDCA DC conduit adapter, pictured above...................$45
I-OBK FXACA  Cover for AC terminals, pictured above.............$45
OUTBACK PSX-240 TRANSFORMER This 6kva auto transformer with cooling fan can be used for step-up, step-down, generator and split phase output balancing or as a series stacked inverter to load balancing auto-former. Incorporating a transformer with 120v 30 amp primary and secondary side, a temperature activated cooling fan and a 25 amp dual breaker in a steel enclosure. the PSX-240 is ready for your custom 120 or 240v 60hz only system.
I-PSX240..................shipping $32................$520
I-X240 Transformer for simultaneous 120/240 volt AC output; does NOT includes an enclosure and has no breakers......shipping $32......$495
Each inverter requires battery cables with lug ends. Outback power system includes this inverter.

Return to the top

OUTBACK MATE
 FOR OUTBACK VFX/FX INVERTERS & MX60 CONTROLLER

Outback MATE is a programming input device as well as meter display, which can mount at the power room or remotely. It plugs into the FX2000/2500 inverter to program any of the adjustable settings for battery charging or start-up sensitivity, automatic start for an engine-generator, etc... The inverter can operate perfectly without the MATE after being set-up once, because your settings stay in memory even if all power is disconnected.

The same MATE also connects to the Outback MX60 solar control as a remote meter and adjustment for the MX60. 

To connect to more than one inverter or inverter and charge control at the same time requires the HUB-4 adapter. MATE includes RS232 port & DB9 for computer datalogging.

C-MATE OUTBACK control and meter with 50 ft. cable...........$295
I-HUB-4 OUTBACK connects MATE to up to 4 inverters and/or solar controls at the same time without switching any cables.....................................................................$195

 Xantrex ProSine 2000 
TRUE SINE WAVE

2000 WATT INVERTER with 100 amp charger and remote control 12 volt only

The ProSine 2000 is the right size and price for many home or mobile power systems. 2000 watts continuous sine wave, 4500 watt surge power for 5 seconds, plus 3-stage standby 100 ampere battery charger. Included LCD display and control panel with 70 ft. cable can be remote mounted. Efficiency is 89%. Automatic idle mode (under 2 watts) when there is no load saves power. Output is true sine wave, 60 Hz within 0.05% crystal controlled. Inverter operates with input battery voltage 10 to16 volts. Protected against short circuit, over-temperature, overload, and low voltage. Two ProSine 2.0 inverters can be stacked to create 120/240 volt system if needed. Operating temperature 0° F to 158 ° F gives better cold tolerance.

STANDBY CHARGER: 30 amp AC transfer relay passes utility or generator power to house when generator or utility is connected, and charges battery. Automatically switches back to inverter within 16 milliseconds when generator (or utility) cuts off. Maintains 100 amp charge with AC input as low as 90 volts. Battery charger adjusts for wet, AGM or gel batteries and includes manual equalization mode. Battery temperature sensor is included, adjusts charge voltage for hot or cold batteries. To avoid exceeding the amp rating of your generator or "shore" power, the battery charger can automatically back-off the charge rate when you operate large AC loads. Includes hardwire terminals for AC in and out connections. No on-board outlets.

I-PRO 2000/12......shipping $25....$1600.00
I-PROPACK 2000 /12 volt:  *$1,800 Factory Special Price includes ProSine 2000, a 400 amp fuse and fuseholder for the inverter and a  Xantrex C-35/DD solar charge control. Limited time promotion!
Shipping in 48 states $25

Each inverter requires battery cables with lug ends.

Backwoods Solar takes used trade-ins of  inverters in our catalog toward purchase of a new inverter.

Return to the top

ENPHASE 190 GRID-CONNECTED MICROINVERTER 

Most grid-connected solar energy
installations use a single centralized inverter to convert the DC output from multiple solar modules into AC power. The Enphase Energy micro-inverter system mounts behind the module and converts the DC output of the solar module into grid-compliant AC power. This simplifies the installation, increases efficiency, avoids high voltage DC wiring and the requirements for conduit and DC switchgear. The 240 volt AC output of the inverter is connected to a 240 volt 15 amp circuit breaker in your house load center through an AC installation kit (sold separately), and up to 14 more inverters can be plugged together to feed the same circuit. If you do not have an unused breaker in your house load center, you may need to have one installed. Warranty is 15 years.

One AC installation kit is required for each 15 inverters. The Multi-contact cables from each solar module simply plug into an Enphase inverter’s input cables. (The DC input wires are approximately six inches long and are terminated with single pole MC connectors.) Each Micro-inverter comes with one 4 pin bulkhead receptacle and one 70-inch AC wire harnesses with multi-pin connectors. The AC connectors are oppositely sexed, so that multiple inverters can be connected to form one continuous AC branch circuit. If any of the inverters are mounted more than 80 inches apart, use an extension cable to tie them together. The Enphase M190 Micro-inverters are designed to operate with most 60 and 72-cell PV module configurations, up to 240 watts. Be sure to verify the voltage and current specifications of your PV module match with those of the Micro-inverter. Inverter weighs 4.4 pounds and is 8” x 5 1/4” x 1 1/4” not including cables.

The Envoy communications gateway collects performance information for each solar module in a user’s system and transmits data to the Enlighten™ website, where users can view their solar power system performance. The Envoy can be plugged into a 120v AC outlet. Enphase Micro-inverters transmit data over the existing power line, so no additional wiring is required. Simply connect an Ethernet cable from the Envoy into a broadband router. It comes with a 90-day Enlighten subscription. Additional monitoring with the Enlighten program can be purchased at $2 per inverter for and additional year, or $9 per inverter for an additional 5 years. The Enlighten website provides information on solar system performance. A graphical representation of the solar array provides information on the status of each module.

EXAMPLE INSTALLATION DIAGRAM

Item #	Additional Information	Price	Price
I-ENPHASE M190	190 watt w/ MC4 cables -shipping $12	$215
I-ENPHASE AC	AC branch circuit installation kit	$68
I-EPHASE-6	6 foot AC extension cable	$73
I-ENPHASE-12	12 foot AC extension cable	$92
I-ENVOY	Communications gateway w/90 days of Enlighten - shipping $12	$347

Return to the top

---

TRUE SINE WAVE
Xantrex  PRO-SINE (TM) 1000 & 1800

12 volt models (24 volt are discontinued or have limited availability)
weight 16 pounds
size 16"W x 11"D x 5"H

Pro-Sine is a true sine wave inverter with compact and lightweight chassis. Goes to automatic power-saving search mode when no power is used. These models have NO internal battery charger. See companion 12 volt battery charger. CSA approved to UL standards. Not for outdoor installation, operating temperature 32-140º F. 2-year warranty.

Backwoods adds the hard-wire terminal connection option,  for code compliant installation in homes, and transfer relay option connects house to generator power when generator runs, and back to inverter when generator goes off. Can also back-up utility power, cutting inverter in automatically upon utility outages. No AC outlets on board.

LCD meter control panel shows battery voltage, amps from battery, and bar graph of AC output watts. Indicates overload, overheat, high or low voltage. Panel can be remote mounted with purchase of interface below. Factory brochures available by request on these models. 

ProSine 1000 is 1000 watt continuous, 1500 watt surge for 5 seconds. I-PROSINE 1000/12 volt:  $850 (shipping in 48 states $20)
I-PROSINE 1000/24 volt:  $925 (shipping in 48 states $20)	Discontinued 1 Left, please call
ProSine 1800 is 1800 watt continuous, 2900 watt surge for 5 seconds. I-PROSINE 1800/12 volt:  $1215 (shipping in 48 states $20)
I-PROSINE 1800/24 volt:  $1330 (shipping in 48 states $20)	LIMITED AVAIL Please call
I-Prosine Remote Interface 30' to remote mount the on-board control panel:  $50

Each inverter requires battery cables with lug ends.

Backwoods Solar takes used trade-ins of  inverters in our catalog toward purchase of a new inverter.

Return to the top

SMALLER TRUE SINE WAVE INVERTERS

A Small True Sine Wave Inverter can solve the problem of a few low-wattage appliances that require only true sine wave power, without upgrading your whole-house inverter to true sine wave. A small inverter can be dedicated to just the computers, a computerized sewing machine or recording equipment. Newly designed for heavy-duty industrial and commercial applications, the Samlex Cotek 600 has two, on board, GFCI protected outlets. Equally robust, the Sure Sine 300 must be hard-wired. Both models offer extensive electronic protection against reverse polarity, overload, short circuit, over/under voltage, and over temp. Two year warranty.

SAMLEX COTEK 600 WATT 12V
600 watts continuous, 680 watts for 3 minutes, and an 800 watt surge. Includes battery terminal lugs that you crimp to 4 gauge copper wire that you provide. Use a 100 amp fuse in the (+) battery cable. No load current consumed is 0.87 amps. Do not connect to an AC breaker panel. On board load controlled cooling fan. Rated operating range:0° to +30° C (+/-10%). Input voltage: 10.5-15.0. 12"x7"x3" 5.4 lbs, UL Listed

I-SAMLEX COTEK 600 12 volt....................$395 (shipping $10)

MORNINGSTAR SURE SINE 300 WATT 12V
300 watts continuous and a 15 minute 600 watt surge. Battery terminals accept 2 gauge copper wire. Use a 100 amp fuse in the (+) battery cable. Current consumed while powering a load is 0.45 amps. With no load, a standby mode is entered which reduces current draw to 0.055 amps. OK to connect to an AC breaker panel. Designed such that an onboard cooling fan is not required. Rated operating range: -40° to +45° C. Input voltage: 10.0-15.5. 8.4"x6"x4", 10 lbs

I-Sure Sine 300.....Shipping $12.......$285

Return to the top